faq: add initial gphoto2 preview instructions

Change-Id: I6a81e6950faf2367c86af2c97204247470df4b8b

Author: andi34

faq/faq.md

@@ -218,11 +218,27 @@ There's different ways depending on your needs and personal setup:
     - Admin panel config *"Preview mode"*: `from URL`
     - Admin panel config *"Preview-URL"* example (add needed IP address instead): `url(http://127.0.0.1:8081)`
 
-    **Note**
+    **Note**  
     - Do NOT enable *"Device cam takes picture"* in admin panel config!
     - Capture pictures via `raspistill` won't work if motion is installed!
     - Requires Photobooth v2.2.1 or later!
 
+3. A device independent preview can also be done using the video mode of your DSLR (Linux only):  
+    - install all dependencies `sudo apt install ffmpeg v4l2loopback-dkms -y`
+    - create a virtual webcam `modprobe v4l2loopback exclusive_caps=1 card_label="GPhoto2 Webcam"`
+      - `/dev/video0` is used by default, you can use `v42l-ctl --list-devices` to check which `/dev/*` is the correct one:  
+        If it doesn't match the default setup you need to adjust the `Command to generate a live preview` inside the admin panel!
+    - Give permissions to /dev/video* `sudo gpasswd -a www-data video` (this was done automatically if you used the installation script) and reboot once
+    - Admin panel config *"Preview mode"*: `from gphoto2`
+
+    **Note**  
+    - Requires Photobooth v2.11.0 or later!
+    - There's a delay of about 3 seconds until the preview starts, to avoid that disable the `Battery saving mode on gphoto2 live preview` option to generate a preview in background. **This results in a high battery usagage and also a general slowdown.**
+    - Sometimes Chromium doesn't detect the V4l2 camera launch from php: you need to run `sudo gphoto2 --stdout --capture-movie | ffmpeg -i - -vcodec rawvideo -pix_fmt yuv420p -threads 0 -f v4l2 /dev/video0` from terminal first and load chrome a first time with a webpage asking for the camera.
+    - Chromium sometimes has trouble, if there is another webcam like `bcm2835-isp`, it will take it by default instead. Disable other webcams, e.g. `rmmod bcm2835-isp`
+    - Make sure the countdown is long enough to start the preview and free gphoto2 at the end of the countdown to be able to take a picture (2 seconds before the countdown ends)
+      - For best used experience the countdown should be set at least to 8 seconds
+
 <hr>
 
 ### Can I use a live stream as background?

manual/faq.html

@@ -263,11 +263,28 @@ <h3>How to use a live stream as background at countdown?</h3>
 <ul><li>Admin panel config <em>"Preview mode"</em>: <code>from URL</code></li>
 <li>Admin panel config <em>"Preview-URL"</em> example (add needed IP address instead): <code>url(<a href='http://127.0.0.1:8081'>http://127.0.0.1:8081</a>)</code></li></ul>
 
-<p><strong>Note</strong></p>
+<p><strong>Note</strong>  </p>
 
 <ul><li>Do NOT enable <em>"Device cam takes picture"</em> in admin panel config!</li>
 <li>Capture pictures via <code>raspistill</code> won't work if motion is installed!</li>
 <li>Requires Photobooth v2.2.1 or later!</li></ul></li>
+<li><p>A device independent preview can also be done using the video mode of your DSLR (Linux only):  </p>
+
+<ul><li>install all dependencies <code>sudo apt install ffmpeg v4l2loopback-dkms -y</code></li>
+<li>create a virtual webcam <code>modprobe v4l2loopback exclusive_caps=1 card_label="GPhoto2 Webcam"</code>
+<ul><li><code>/dev/video0</code> is used by default, you can use <code>v42l-ctl --list-devices</code> to check which <code>/dev/*</code> is the correct one: <br />
+If it doesn't match the default setup you need to adjust the <code>Command to generate a live preview</code> inside the admin panel!</li></ul></li>
+<li>Give permissions to /dev/video* <code>sudo gpasswd -a www-data video</code> (this was done automatically if you used the installation script) and reboot once</li>
+<li>Admin panel config <em>"Preview mode"</em>: <code>from gphoto2</code></li></ul>
+
+<p><strong>Note</strong>  </p>
+
+<ul><li>Requires Photobooth v2.11.0 or later!</li>
+<li>There's a delay of about 3 seconds until the preview starts, to avoid that disable the <code>Battery saving mode on gphoto2 live preview</code> option to generate a preview in background. <strong>This results in a high battery usagage and also a general slowdown.</strong></li>
+<li>Sometimes Chromium doesn't detect the V4l2 camera launch from php: you need to run <code>sudo gphoto2 --stdout --capture-movie | ffmpeg -i - -vcodec rawvideo -pix_fmt yuv420p -threads 0 -f v4l2 /dev/video0</code> from terminal first and load chrome a first time with a webpage asking for the camera.</li>
+<li>Chromium sometimes has trouble, if there is another webcam like <code>bcm2835-isp</code>, it will take it by default instead. Disable other webcams, e.g. <code>rmmod bcm2835-isp</code></li>
+<li>Make sure the countdown is long enough to start the preview and free gphoto2 at the end of the countdown to be able to take a picture (2 seconds before the countdown ends)
+<ul><li>For best used experience the countdown should be set at least to 8 seconds</li></ul></li></ul></li>
 </ol>
 
 <hr>